Tungsten Break-Off Points for Easton X10 & Pandarus 3.2mm
Tungsten Break-Off Points for Easton X10 & Pandarus 3.2mm
Shore Shot 97% tungsten points for Easton X10, X10 ProTour, Pandarus CA320-XT, and Zone Podium X A/C / Arena / Speed X 3.2. Buy a matched dozen or a single point. Break-off options cover 140 gr down to 60 gr so you can change FOC without a new dozen every time.
Fit
Easton X10, Easton X10 ProTour, Pandarus CA320-XT, Zone Podium X 3.2 mm shafts, and other arrows that take a 3.2 mm / 0.125" OD tungsten point.
Weights
Listed weight Break-offs Notes
90 gr 80 / 70 / 60 gr Gold only
100 gr None Solid
120 gr 110 / 100 gr Most common recurve dozen
140 gr 130 / 120 gr Heavy FOC / compound
Dozen: matched ±0.3 gr
Single point: ±0.5 gr, not guaranteed to match a dozen
Build
97% tungsten, titanium plating, glue cutout under the head, 6 glue grooves, OD 0.125".
Shot with Shore Shot tungsten
Men’s individual Olympic silver, 2024
Individual Paralympic gold, 2020
Men’s recurve double 70 m 1,367 world record
Install (hot melt)
Records
Men’s Individual Olympic Silver Medal 2024
Individual Paralympic Gold Medal 2020
Mens Recurve Double 70M 1, 367 World Record
WHY Titanium Plating?
Reasons to implement a titanium electroplating process include enhancing the metal's ability to resist surface fatigue and fretting and anti-galling properties. Titanium substrate plating can also be used to improve the following scenarios: Corrosion resistance in hot acidic environments.
WARNING: cancer and reproductive harm - www.P65Warnings.ca.gov
*Color may ware after extensive use
*Hitting objects other then target bales may cause point damage or breaks
*Reminder, EU customers will be responsible for paying VAT on pickup.
*Purchases outside of the United States may be subject to local taxes on delivery or additional shipping costs
Recommended Point Installation Method
(Tool Required: A butane or propane torch with small flame, pliers, cleaning materials noted below, and recommended hot melt (CDM Flitemate Hot Melt or Shop Stick)
Cut arrow shaft on high speed arrow saw and deburr the inside of shaft, removing no more then 1/4” of aluminum shaft wall
Clean the inside of the shaft (about 2” in) with 91% isopropyl alcohol
Heat hot melt in a gas flame and apply a ring of hot melt around and inside the open end of the shaft (Never Apply Heat Or Flame To The Shaft)
With your small set of pliers, grasp the point and coat the shank end of the point with hot melt that was headed by your hot flame (get hot melt soft not liquid)
Hold the point in your piers with the hot melt applied into the flame again, this time let it liquefy (MAX 3-4 Seconds Do Not Overheat the Point) Serious damage to the shaft or point could occur
Put point into shaft with a twisting motion. Quickly reheat THE POINT ONLY IF NEEDED to get in fully into the shaft. Whip excess glue with a paper towel
Stand the shaft on the point end making sure the point is completely seated in the shaft and allow it to cool before touching our shooting, DO NOT use water to cool the shaft and point
Adjusting Point Weight
Required Tools: 2 Small Pliers and Safety Glasses
Only applies to 120 grain and 140 grain points
To remove 1st break-off (lose 10 grains) Use one pair of pliers to grasp the INNERMOST weight segment and with the other pair of pliers break off the outermost segment
To remove 1st and 2nd break-off (lose 20 grains) Use one pair of pliers to grasp the shank of the point and with the other pair of pliers break off both weight segments